Before you try anything: always speak to a professional before cleaning, treating or applying any product to your stone. Every slab is different, and the wrong product can cause permanent damage. Contact us or a qualified stone restorer first.
Quick answer
Red wine stains in travertine lift with a hydrogen peroxide poultice: blot the wine immediately, wash the area, then leave the poultice covered for 24 to 48 hours to draw the colour out. Wine is acidic, so on travertine a dull ring may remain after the colour is gone; that is an etch and is fixed by polishing.
First, check what you are dealing with
- Purple, pink or grey-blue mark: a wine stain. Follow the steps below.
- Pale, dull ring where the glass stood: an etch from the wine's acidity.
What you need
- Paper towel
- pH-neutral dish liquid
- Hydrogen peroxide
- Flour, talc or diatomaceous earth
- Plastic wrap and tape
- Plastic scraper
Step by step
Blot fast
Blot up every drop straight away. On travertine, the first few minutes decide how deep the colour goes.
Wash the area
Clean with warm water and a few drops of pH-neutral dish liquid, rinse and dry with a soft cloth so you can see what is left on the travertine.
Test first
Try the mixture on a hidden spot of your travertine (inside a cut-out or under an overhang) and check the finish after it dries.
Mix the poultice
Stir an absorbent powder (plain flour, talc, diatomaceous earth or whiting) into hydrogen peroxide (3% from a pharmacy for fresh stains, or 12% from a hairdressing or pool supplier for older ones) until it has the consistency of peanut butter.
Apply it
Spread it 5 to 6 mm thick over the wine stain, extending about a centimetre past the edge. Cover any filled holes inside the stained area too: fills hold stains as well as the stone does.
Cover and wait
Cover with plastic wrap, tape the edges and poke a few small holes so it dries slowly. Leave it 24 to 48 hours until completely dry: the drying is what pulls the stain up into the powder.
Remove and rinse
Lift the dry poultice with a plastic scraper, rinse with clean water and dry the travertine. If the wine stain is lighter but still there, repeat up to three times.
What not to use on travertine
- Vinegar, lemon juice or "natural" citrus cleaners: they etch travertine.
- Scourers, steel wool and abrasive creams on a polished surface.
- Mixing cleaning chemicals, especially bleach with anything else.
- Salt, soda water and white wine "tricks": they do nothing for stone and can spread the stain.
When to call a professional
If colour remains after three rounds, or you are dealing with a large etched area, call a restorer. A stone restorer can refill open holes, re-hone the surface and blend repairs into the surrounding stone.
Understanding red wine stains on travertine
Travertine is full of natural cavities that are filled with resin or cement, and the stone between them is porous. Coffee, wine and oil soak in quickly, and fills can take stains differently from the stone.
Travertine is a limestone deposited by mineral springs, so it is calcium carbonate and etches as readily as marble.
A stone restorer can refill open holes, re-hone the surface and blend repairs into the surrounding stone.
Good to know
Wine on travertine tables often runs into the fills around the edge of the glass. Poultice the fills along with the stone.
Stop it happening again
Whether yours is ivory, beige, walnut and silver travertine, vein cut or cross cut, repairing it fixes today's mark; protecting it stops the next one. Our clear Stone Protection Film sits over the surface, so acids cannot etch it and liquids cannot soak in. Most travertine is honed and filled, so the Matte/Satin film is the usual match: it keeps the natural, low-sheen look. It is installed across Sydney with a 10-year written warranty.
How we protect travertine · Stain removal guide · Red wine stains on every surface